Compact Stainless Steel Vacuum Glove Box(22x17x16) with Vacuum Flange & Gauge. EQ-VGB-1 is a small size stainless steel glove box with Airlock Chamber, Gauges and vacuum Flanges, which allow glove box operate under vacuum to remove moisture and oxygen without expensive inert gas purging, It is an ideal tool for material and chemical researchers to process air sensitive materials and solutions.Case Material: Made of 11 gauge (3mm thickness) 304 stainless steel sheet with support frame, which provides heavy duty structure for vacuum. Dimensions: 555mm(L) x 444mm(W) x 414mm(H).
Positive Pressure: 810 Torr (1.1 atm). Note: Gloves cannot work if pressure is higher than 810 Torr. Vacuum Level: 0.5 Torr.Note: Stainless Steel case may deform at higher vacuum level. Dimensions: 200mm(ID) x 270mm(L). Vacuum Level: 0.05 Torr. Two vacuum flanges are included for glove box to achieve vacuum to remove moisture and oxygen without expensive inert gas purging. Do not operate under vacuum? Vacuum is used for purging the chamber before operation.
One KF-25 connector is installed on the back for connecting humidity monitor or other testing equipment On the Glove Box Chamber Dimension On the Air-lock Chamber. One extension socket (Max power 1500W) is installed in the glove box main chamber. Note: 110V power cord was included for immediate use.
(For 208240V power supply, no plug will be included). One pair of Latex Gloves are included for immediate use.Optional: You may order 6'' Butadyl® gloves here because they have. Increased stretching, bending ability and tear strength.
High effectiveness when vaporized hydrogen peroxide (VHP) is present. High resistance to aromatics, hydrocarbons, solvents, fats, and acids. Vacuum pump and Pressure Controller (Optional).Vacuum pump and fittings are not included. (Please order separately under Personalization). Note: A KF25 Vacuum Right-Angle Valve is necessary for connecting to a vacuum pump, please order it accordingly. 1186mm(L) x 480mm(W) x 490mm(H).
Corrosive liquid (such as LiPF6 electrolyte) must be remain sealed in a container inside the glove box. Otherwise, liquid vapor may condense and corrode the steel chamber and purification pipeline.The H2O & O2 removing rate is largely dependent on the type of purging gas used. For faster chamber purging process, Nitrogen is preferred over Argon due to its lighter mass. By closing the vacuum flange, the glove box can be vacuumed by mechanical pump upto 0.5 torr before filling inert gas. The moisture can be reduced below 50 ppm by vacuuming the glove box.
After refilling the glove box with high purity Argon gas (5N purity), the glove box moisture can be kept below 180 ppm-40? Dew point and oxygen below 200 ppm. In this way, you can save 1-2 tank of inert gas from purging at each operation. 16 pins electrical feed through outside the glove box (4 pins per one feed through).16 pins electrical feed through inside the glove box (4 pins per one feed through). You may choose device below to monitor gas humidity and oxygen content inside the glove box. Digital Humidity & Temperature Monitor. Trace Oxygen Analyzer (0.01 -3000PPM) with KF40 Connector. Warning: This glove box is not suitable for Li-ion battery research because the humidity cannot be lowered to 10ppm. Please order VGB-5, VGB-6, or VGB-7 or purification system for Li-ion battery research.
We will give the best service. Negative and neutral feedback does no good to both of us. With a better communication, any tricky issue could be solved.
Every customer counts, trust us, we will not let you down. This item is in the category "Home & Garden\Tools & Workshop Equipment\Other Tools & Workshop Equipment". The seller is "hansunthermal" and is located in this country: CN.
This item can be shipped worldwide.